I don't have three acres but a 3 year old home on 3/4 acres. I have an older JD-LT155 with a 38" mower deck. It has no problems with the slopes, in fact it surprised me when it was able to climb out of the ditch in the front yard. While there are many solutions to the mowing problem, there are other uses for a tractor. I would recommend a tractor either one like the LT-155, or one of the heavier ones. With three acres and your desire to make additional planting, you will appreciated the tractor with a trailer to move all of the tools, plants, seeds, mulch, fertilizer, and things yet to be discovered that those flower beds and new trees will need. Right now I am looking at putting a water tank in the trailer to water those new remote plantings. If you can afford two I would get a tractor and the zero turn.

Must of been lucky. Bought an MTD at Ace hardware (Ace Special Edition) with a 42" cut and 16hp Tecumseh. Aside from the normal problems of your MTD of that era IE having the grille mounts break off after a few years) it's been great, and it was only replaced as it was really starting to not work well on hills, and in the last year has been a case of "What's going to break next when I mow?". A key to remember is any NEW tractor in that range is going to be light duty. If you have more an acre to mow with it, a newer, higher end, used model is a probably a better option. You'll get a lot of life out of one though if you keep it well maintained. Take care of it and there is no reason why you should not get a good, usable life of about 10-12 years. one other thing to keep in mind; the chief complaints of many people on a mower it seems is the motor. That is the most important part of a mower besides the transmission on a Hydro equipped tractor. The engine is going to what will go wrong 9 time out of 10 on a mower, and is often going to be to blame for issues with cutting (due to lack of power) and reliability.

This is my first time on here, so I don't exactly know how to post so here goes. My JD-425 has a flooding problem. Sometimes it runs ok, and sometimes not. When I turn on the ignition, the fuel pump starts (as normal) and I can usually start it. Then, after running for a while, it begins flooding. This is between 15 minutes and half an hour most of the time. I can keep it running if I go full throttle and have the tractor under load, like mowing grass, but there is so much gas entering the carb that there is a bit of black smoke as well. If I stop it and remove the air cleaner, and look into the carb, there is gas everywhere. Here is what I did so far... The carb was new 3 years ago. But I removed it, and took it apart (did this 3 times). Each time I took it apart and put it back together, I know I did it right because the machine started and ran as noted above. I thought it just might be plugged or something. The first time I took it apart I also replaced the electric solenoid valve, just to be sure. And I know it works, because I saw it operating with the carb disassembled. Then, I thought it might be that the float valve was leaking or perhaps the floats had a hole and was full of gas. All was good. When the carb was back together, I blew into the fuel hose when the carb was full of gas and proved that the float valve was working. Hmmm. There is a manual in-line fuel shutoff valve, so what I did was throttle it back so that it would take 30 seconds to to let about an ounce of fuel out. Full blast, the pump actually pumps a lot of fuel. This time, I was able to keep the machine from flooding too bad. And was able to mow the 1 acre of grass I have. Today, however was different. It ran for about 5 minutes, then began to act up. I turned it off, removed the air cleaner and looked into the carb. When I turn the ignition switch on, (not engaging the starter) I can see tons of gas coming out of every carb orifice, flooding into the engine gas everywhere. This is without the engine running. The only thing I can come up with is that the fuel pump for some unknown reason has too much pressure behind it. Another wierd thing is that when I turn a sharp corner, under the flooding condition, the flooding gets noticably worse. Any ideas anyone? Is there a pressure regulator somewhere in the fuel pump line? Thanks.

reply by theodocus struck me as coming from the desk of the ad agency of MTD. No mention of the actual operation that involves rolling over uneven terrain and jarring action from bumps and uneven spots and the fragile fabricated axles that bend and crack easily. Oh, there is also the bushings used in place of ball bearings: bushing use requires higher horsepower to move the newer units. The Deere has points and condenser; cost $5.00 and 9.00 respectively and the sears is a solid state igntion. Newer technology is wonderful as long as it is coupled with quality assemblage in a product. I have a 1968 Sears GARDEN tractor with a 12HP Tecumseh Heavy duty cast iron engine with ball bearings and cut with a 42 inch deck and also have a 1976 John Deere GARDEN tractor with a cast iron 10 HP engine with ball bearings and cut with a 42" deck and use both alternately for mowing two acres and for tilling and moving earth, etc.. Each has cast iron axles and mutli-speed hi-lo transmissions and EACH is used for plowing, snowblowing, tilling earth, hauling 1100 lb loads in attached large carts. EACH will run circles around the new 20 plus HP light LAWN tractors made today. Spend 5,000.00 and you will have a comparable heavy duty GARDEN tractor. By the way, good luck on getting even 10 years of use with the new wonders.